SII IP-6900 User Manual Download

Page: 193 / 266

3-65

Section 3 Operation Panel Menu Operations

(12) HEB board version display

Displays the HEB board version.

<Parameter (Execution form)>
None

(13) SCSI ID number display (SCSI ID)

Displays the SCSI ID number set with the rotary switch on the
SCSI board.

<Parameter (Execution form)>
None

(14) System date setting (SYSTEM DATE)

Sets system date used internally in the printer in the order of YY
(year), MM (month), DD (day).

<Parameter (Enter a value)>
00/01/01 to 99/12/31

(15) System time setting (SYSTEM TIME)

Sets system time used internally in the printer.

<Parameter (Enter a value)>
00 : 00 to 23 : 59

#SYSTEM TIME

>00 : 00

#DATE (YY/MM/DD)

>03 / 08 / 01

X: ID number

#SCSI ID

✽

ID : X

X: ID number

#HEB VERSION

✽

X.X

Menu Operations

Summary of Contents for IP-6900











































































































































































































































































Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands

SII IP-6900, User Manual

Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands