SII IP-6900 User Manual Download

Page: 80 / 266

2-36

Set the printer to OFFLINE mode.

(Press the

key)

Press the

key, and then the

key to display a

feed adjustment pattern.

#FEED PATTERN

✽

ROUGH (NORMAL)

Select the print mode you usually use for the media to which the feed
correction value is set.

For details of the print modes, see page

4-2

"Print Modes"

INK

ENTRY

PAPER

F. ADJ

Feed Correction Value Setting

The feed correction value is changed by the following causes:

• Backing sheet is used/not used

• Print mode is changed

• Pressure is changed by the media pressure alternation

lever

• Winder is used/not used

• Media type

• Media feed path is different

• Feed mode "SEQUENCE 1" or "SEQUENCE 2"

Set media of length longer than 1 m.

For the feed correction, obtain approximate feed correction value in the
ROUGH mode, and set exact correction value in the DETAIL mode. One

printing requires a media length of 48 to 58 cm in the ROUGH mode, or 27
to 32 cm in the DETAIL mode. (Printing of the feed adjustment pattern can

be cancelled by pressing the

key.)

HINT

Summary of Contents for IP-6900











































































































































































































































































Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands

SII IP-6900, User Manual

Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands