SII IP-6900 User Manual Download | Manualshive

Page: 169 / 266

background image

3-41

Section 3 Operation Panel Menu Operations

(33) Deleting registrated media (DELETE MEDIA)

Deletes a registered media.
Registered media from 01 to 20 can be selected.
The registered media 01 is defined as the standard media. This
cannot be deleted.
When the

key is pressed, confirmation guidance will be

displayed.

(34) Parameter copy source

Register the copy source of the registered media numbers.
Setting of this parameter and

(35) Parameter copy destination

copies the registered media information.

<Parameter (Enter a choice)>
- Value:

01 to 20
However, only the registered numbers are displayed.

(35) Parameter copy destination

Select the copy destination number of the registered media.

<Parameter (Enter a choice)>
- Value:

01 to 20
"

✽

" is displayed for an already registered number.

#DELETE PAPER

>01 : TYPE02

#DELETE PAPER

>01 : TYPE02 OK?

# COPY SOUCE

>01

# COPY DEST

>01

→

01

✽

Menu Operations

«
...
167
168
169
170
171
...
»

Summary of Contents for IP-6900











































































































































































































































































Reviews:

No comments

Related manuals for IP-6900

Brand: SPRT Pages: 28

DocuPrint C3055 DX

Brand: Xerox Pages: 20

Brand: Lexmark Pages: 500

Brand: DNP Pages: 66

Brand: Xerox Pages: 2

SignJet JS310 Series

Brand: GRAPHTEC Pages: 83

Brand: Noztek Pages: 8

PIXMA E300 series

Brand: Canon Pages: 28

Brand: Canon Pages: 115

Brand: Canon Pages: 124

Brand: Canon Pages: 216

PIXMA iP7200 Series

Brand: Canon Pages: 5

Brand: Brother Pages: 401

Brand: WOOSIM Pages: 19

Brand: Infinite Peripherals Pages: 29

Brand: WOOSIM Pages: 24

Brand: Konica Minolta Pages: 150

Brand: MF DIGITAL Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands