SII IP-6900 User Manual Download

Page: 33 / 266

1-11

Section 1 Getting Started (Basic knowledge)

Consumables

WARNING

- Do not swallow ink or let it splash on the eye. If it gets into

the eye, wash it off with clean running water and consult a

doctor. If it is swallowed, do not try to force vomiting, but see

a doctor.

- Install the waste ink bottle securely.

- A waste ink bottle must always be installed. If it is removed

for replacement, a new one must be installed.

CAUTION

NOTE

- Never put the waste ink bottle near an open flame. Failure

to follow this warning might result in fire.

Item No.

Remarks

IP6-109

1 piece

Waste Ink Bottle

Use our recommended waste ink bottle listed below.

Precautions for handling the waste ink bottle

- After use, securely fasten the attached cap and dispose of

the waste ink bottle as industrial waste.

CAUTION

Summary of Contents for IP-6900











































































































































































































































































Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands

SII IP-6900, User Manual

Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands