SII IP-6900 User Manual Download | Manualshive

Page: 179 / 266

background image

3-51

Section 3 Operation Panel Menu Operations

(4) Filling ink to the cap (FILL CAP)

Fills the ink into the cap and soaks the head (nozzle surface) into
the ink for 1 to 2 hours to remove nozzle clogging.
Use this menu when dot-off in printing cannot be eliminated by
cleaning repeatedly.

<Parameter (Execution form)>

None

- Always perform cleaning (slight) after filling cap action.

- If dot-off in printing cannot be eliminated when leaving the

printer for 24 hours, contact our service center.

NOTES

#FILL CAP

>

Menu Operations

«
...
177
178
179
180
181
...
»

Summary of Contents for IP-6900











































































































































































































































































Reviews:

No comments

Related manuals for IP-6900

PIXMA MX882 Series

Brand: Canon Pages: 34

Brand: Canon Pages: 4

Brand: Canon Pages: 913

Laser Class 700 Series

Brand: Canon Pages: 30

Laser Class 700 Series

Brand: Canon Pages: 6

Laser Class 700 Series

Brand: Canon Pages: 6

Laser Class 700 Series

Brand: Canon Pages: 108

PIXMA MX860 series

Brand: Canon Pages: 9

imagePROGRAF iPF9400

Brand: Canon Pages: 8

PIXMA MX860 series

Brand: Canon Pages: 93

Brand: Canon Pages: 20

Brand: Canon Pages: 30

Brand: Canon Pages: 2

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 97

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 151

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 120

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 97

SCX 4200 - B/W Laser - All-in-One

Brand: Samsung Pages: 95

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands