SII IP-6900 User Manual Download

Page: 99 / 266

2-55

Section 2 Basic Operations

Head Cleaning "CLEANING"

This section explains how to clean the head.
Three types of cleaning are available. Use either one according to
the application.

Put the printer offline. (Press the

key.)

Press the

key to display the CLEANING menu.

Press the

key to enter the head cleaning menu.

INK

ENTRY

PAPER

F. ADJ

SERVICE

FEED

CLEANING

INK

ENTRY

PAPER

F. ADJ

# CLEANING

>NORMAL

Cleaning type

Application

Ink consumption

NORMAL

Recovery from dot-off in printing

2.45 cc

STRONG

Recovery from jam
Recovery from dot-off in printing
if NORMAL fails to recover

10.82 cc

Summary of Contents for IP-6900











































































































































































































































































Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands

SII IP-6900, User Manual

Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands