SII IP-6900 User Manual Download

Page: 244 / 266

5-6

Parameter Setup Mode

This mode is used when the operator sets the heater system control
parameters.

(1) Setup items and parameters

The setup items and parameters are listed in the table below.

*1 Display only, ON/OFF key is ignored.

(2) Entering the parameter setup mode

Press the ON/OFF key,

key, and

key on the heater control

panel at the same time to enter to the parameter setup mode.
The 1st setup item in the parameter setup mode will be displayed.

Note: # will blink.

# UNIT

> CELSIUS

No.

Item

Item Display

(upper line)

Parameter

Display

(lower line)

Description

Initial value

Temperature unit

UNIT

CELSIUS
FAHRENHEIT

CELSIUS

Heat suspending
time after printing

DELAY TIME

00 to 30 MINUTE

UNIT: minute

05 MINUTES

Standby heating

time after
completion of
DELAY TIME

STANDBY TIME

0, 30, 60, 90, 120,
ENDLESS

Unit: minutes

Version display

VERSION

FW=vv.r HW=vv.r Display only

Diagnostics

DIAGNOSTICS

NO, YES

NO: Does not perform

diagnostics.

YES: Performs

diagnostics.

Display language

LANGUAGE

ENGLISH
JAPANESE

ENGLISH

Exit of setup mode EXIT

YES, NO

YES: Exits from

parameter mode.

NO: Does not exit from

parameter mode.

YES

Summary of Contents for IP-6900











































































































































































































































































Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands

SII IP-6900, User Manual

Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands