SII IP-6900 User Manual Download

Page: 39 / 266

1-17

Section 1 Getting Star

ted (Basic knowledge)

Heater

The printer has three built-in heaters for fixing and stabilizing the
print image on the print media.

(1) Front heater (Front)

Preheats the media.

(2) Print heater (Rear)

Infiltrates ink into the media and fixes ink.

(3) Rear heater (Finish)

Dries ink and stabilizes print image.

* The three heaters are controlled separately.

The heater temperature can be controlled from the operation panel and host
PC (RIP).

(

⇒

See page 2-60 “Changing Heater Control Setting Temperature”)

WARNING

Heaters become hot.

NEVER touch the heaters. Doing so could cause a

burn.

External Views, Part Names, and Functions

Media

Main scroller

Paper feed

direction

Media outlet side

Head

Tension bar

Media inlet side

(1)

(2)

(3)

Summary of Contents for IP-6900











































































































































































































































































Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands

SII IP-6900, User Manual

Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands