SII IP-6900 User Manual Download

Page: 51 / 266

2-7

Section 2 Basic Operations

Turning the Power ON/OFF

Turn the AC 2 switch on the right rear of the printer OFF

(0), and plug one end of the supplied power cable into the

AC 2 socket. Insert the other power plug of the cable into

an electrical outlet.

Turn the AC 2 switch on the right rear of the printer ON (1).

Power cable

NOTES

Do not use a power cable other than the one specified for

this printer.

The supplied power cable is for 200VAC. The shape of the

plug is different from the plug for 100VAC.

Printer switch OFF (0)

Socket

Printer switch ON (1)

CAUTION

Fix the power cable in place using a clamp. If this is not

done, the power cable can be wound up in the scroller,

possibly causing electric shock and damage to the

equipment.

Summary of Contents for IP-6900











































































































































































































































































Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands

SII IP-6900, User Manual

Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands