SII IP-6900 User Manual Download | Manualshive

Page: 90 / 266

background image

2-46

<If the Ink in Main Cartridge is Used Up>

The guidance that prompts you to replace the main cartridge is
displayed on the second line of the LCD. The printing operation
continues until the ink in the sub tank is used up. If replacement is
completed while ink remains in the sub tank, the printing operation
can continue without interruption.
If the main cartridge is not replaced even after the ink in the sub
tank is used up, the print pause mode is activated and the printing
operation is interrupted until the main cartridge is replaced.
To recover from the interrupted state, close the ink cover and press

the

key. The pause mode is then cancelled and printing will

restart.

PRINTING

ROLL: 104 / PAPER

PRINTING

OPEN X INKCOVER

PRINTING

CHANGE YY INK

XXXX: L, R

YY: Bk Lm Lc Y M

C

-

The guidance concerning the ink replacement during the

online printing is displayed on the second line of the LCD

in turn, as the guidance mentioned above.

The printer can restart by operation performed to restart

after an error.

HINT

«
...
88
89
90
91
92
...
»

Summary of Contents for IP-6900











































































































































































































































































Reviews:

No comments

Related manuals for IP-6900

Brand: SPRT Pages: 28

Brand: Samsung Pages: 115

Brand: Canon Pages: 797

LASER CLASS 730i

Brand: Canon Pages: 155

X2650 - Color Printer 3-IN-1

Brand: Lexmark Pages: 2

Brand: SNBC Pages: 78

464de - X B/W Laser

Brand: Lexmark Pages: 27

Brand: iFactory3D Pages: 14

Brand: Muratec Pages: 6

Liquid Crystal Opus

Brand: PhotoCentric Pages: 12

Brand: TRAK Pages: 98

Brand: Konica Minolta Pages: 2

4400B - Phaser B/W Laser Printer

Brand: Xerox Pages: 24

Brand: Xerox Pages: 240

PIXMA MG2220 Series

Brand: Canon Pages: 4

Brand: Canon Pages: 16

Brand: Canon Pages: 28

Brand: Canon Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands