SII IP-6900 User Manual Download

Page: 242 / 266

5-4

Heater

Setup

temperature

Current

temperature

FRONT

AAA

XXX

BBB

YYY

REA

CCC

ZZZ

Celsius

Fahrenheit

Preset temperature

Current temperature

LCD Display

(1) Display in normal mode

Display: (AAA to CCC, YYY to ZZZ)

Temperature unit: (U)

• Preset temperature display

When using a Fahrenheit display, the temperature is displayed
to three digits.
(99

Fahrenheit or less temperature is displayed with a space

plus 2 digits.)

• Display renewal period

The temperature is measured every 5 seconds and the display is
renewed.

(2) Display at heater ON

When each heater is heated, “+” is displayed in place of the unit of
each heater current temperature on the second line. The unit display is
restored at the completion of heating. In the display example shown
above, the front heater is heated.

AAAU BBBU CCCU

XXX+ YYYU ZZZU

Heater ON

AAAU BBBU CCCU

XXXU YYYU ZZZU

Front heater Printer heater

Rear heater

Summary of Contents for IP-6900











































































































































































































































































Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands

SII IP-6900, User Manual

Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands