SII IP-6900 User Manual Download

Page: 118 / 266

2-74

#CAP CLEANING

NOTE

Select the SERVICE menu on the operation panel, then select CAP
CLEANING”.

The head carriage will move to the wipe side and you can easily access

the capping unit.

(The buzzer stops.)

Open the rear cover and cap cover. Wipe the edge and periphery of the

upper surface of all (six) caps carefully with the cleaning swab.

Close the cap cover and rear cover. The head carriage will return to the
capping unit position (home position) automatically.

(The buzzer stops)

Do not leave the printer for a long time with the head

carriage not on the capping unit.

Clean the edge and periphery

of the upper surface of the
cap.

Summary of Contents for IP-6900











































































































































































































































































Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands

SII IP-6900, User Manual

Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands