Siemens Sirius 3RA6 System Manual Download Page 176

Page: 176 / 320

Accessories

7.7 Infeed system for 3RA6

SIRIUS 3RA6 compact starter

176

System Manual, 09/2014, NEB560060102000/RS-AA/006

7.7.3.5

Removing the infeed system for 3RA6 from a standard mounting rail

The infeed system for 3RA6 is either installed on a standard mounting rail or on a level

surface (screw fastening). The removal process is basically the same for both mounting

types. The only difference between the two is how the extension modules are fastened. As

the infeed system for 3RA6 is meant to be mounted on a mounting rail as standard, the

information below describes removal from a mounting rail.

Requirements

DANGER

Hazardous voltage!
Will cause death or serious injury.
Before starting work, disconnect the system and the device from the power supply.

●

The terminal blocks must have been disconnected.

●

The compact starters and circuit breakers must have been removed.

●

The PE infeed and PE tap must have been removed.

Removing screw-type infeed (25/35 mm

) or screw-type infeed (50/70 mm²) from a standard mounting

rail

Step

Instructions

Image

Pull the screw-type infeed down until

it can be pulled away from the

standard mounting rail.

Pull the screw-type infeed away from

the standard mounting rail and lift it

off the rail's upper edge.

Summary of Contents for Sirius 3RA6

































































































































































































































































































































Search results

Summary of Contents for Sirius 3RA6

Reviews:

Related manuals for Sirius 3RA6

Brands by name

Popular brands

Siemens Sirius 3RA6, System Manual

Search results

Summary of Contents for Sirius 3RA6

Reviews:

Related manuals for Sirius 3RA6

Brands by name

Popular brands