Siemens Sirius 3RA6 System Manual Download Page 169

Page: 169 / 320

Accessories

7.7 Infeed system for 3RA6

SIRIUS 3RA6 compact starter
System Manual, 09/2014, NEB560060102000/RS-AA/006

169

Step

Instructions

Image

Push the PE infeed against the right-

hand/left-hand side of the screw-type

infeed or extension module and then

push it upwards.

Press the link wedge down.

Use the PE extension connector to

connect the PE infeed and screw-type

infeed/extension module.

Use the PE extension connector to

connect each additional extension

module to its predecessor.

Working from the bottom, push the PE

tap into the relevant slot on the infeed or

extension module until you hear it

engage.

DANGER

Hazardous voltage!
Will cause death or serious injury.
Unless the extension modules are connected using a PE extension connector, the infeed

system will NOT be grounded.
If you are using the PE infeed and PE tap and decide to expand the infeed system for 3RA6

by adding extension modules, you will need to use a PE extension connector for the

purpose of connecting each additional extension module to its predecessor.

Note
If you are installing the PE infeed on a level surface (screw fastening), it will also need to be

fixed to the surface using an M4 x 16 screw.

Summary of Contents for Sirius 3RA6

































































































































































































































































































































Search results

Summary of Contents for Sirius 3RA6

Reviews:

Related manuals for Sirius 3RA6

Brands by name

Popular brands

Siemens Sirius 3RA6, System Manual

Search results

Summary of Contents for Sirius 3RA6

Reviews:

Related manuals for Sirius 3RA6

Brands by name

Popular brands