Siemens Hicom Office PhoneMail Installation And System Administrator'S Manual Download Page 19 | Manualshive

Page: 19 / 138

background image

FCC and Industry Canada Compliance

lleg_sa.c01

G281-0507-00, April 15, 1998
Hicom Office PhoneMail, Version 1, Installation and System Administration Guide

1-7

Important Notices

Each Siemens switch discussed in this section is capable of providing user access to interstate
providers of operator services through the use of equal access codes. Modifications by aggre-
gators to alter these capabilities is a violation of the Telephone Operator Consumer Services
Improvement Act of 1990 and Part 68 of the FCC Rules.

Electrical Safety Advisory

While each Siemens switch discussed in this section is fully compliant with FCC Rules and
Regulations, it is recommended that an alternating current (ac) surge arrestor of the form and
capability suitable for the model of the system purchased be installed in the ac outlet to which
the system is connected. Consult with your Siemens representative or distributor to determine
the surge protector requirements for your system.

Facility Interface Information for the Hicom 150 E CS, OfficePoint and OfficeCom only

The following tables list facility interfaces, manufacturer’s network interface port designations,
RENs or service codes, and network jacks.

This table lists the network trunk interfaces for loop-start and ground-start services.

This table lists the station interfaces for analog private line (PL) services.

This table lists the network digital trunk interfaces for digital services.

Facility Interface

Manufacturer’s Network Interface
Port Designation

REN

Network
Jacks

02LS2

TMGL4

0.4B

RJ21X

02GS2

TMGL4

0.4B

RJ21X

Analog PL Facility
Interface

Manufacturer’s Network Interface Port
Designation

Service
Code

Network Jacks

OL13B

8SLA (OPS)

9.0 F

RJ21X

OL13B

4SLA (OPS)

9.0 F

RJ2GX

Digital Facility In-
terface

Manufacturer’s Network Interface Port
Designation

Service
Code

Network
Jacks

02IS5

TMQ4 board

6.0 Y

RJ49

«
...
17
18
19
20
21
...
»

Summary of Contents for Hicom Office PhoneMail











































































































































Reviews:

No comments

Related manuals for Hicom Office PhoneMail

Brand: ABB Pages: 138

Brand: ABB Pages: 116

Brand: VDO Pages: 2

Brand: Balboa Pages: 74

Brand: elsner elektronik Pages: 148

MERLIN LEGEND Release 7.0

Brand: Lucent Technologies Pages: 1082

Brand: Parker Pages: 47

Brand: Teac Pages: 16

Brand: Ferguson Pages: 13

bryant ONEBB3ZAC01

Brand: Carrier Pages: 6

Brand: Alpine Pages: 8

Brand: DIS Pages: 54

Brand: Roadstar Pages: 21

Brand: Midland Pages: 24

Brand: Pioneer Pages: 2

Brand: Pioneer Pages: 9

Brand: Pioneer Pages: 96

Brand: Panasonic Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands