SICK Flexi Classic Operating Instructions Manual Download Page 122 | Manualshive

Page: 122 / 156

background image

Chapter

10

Operating Instructions

Flexi Classic Gateways

122

© SICK AG • Industrial Safety Systems • Germany • All rights reserved

8011834/YT28/2016-03-15

Subject to change without notice

PROFINET IO Gateway

10

PROFINET IO Gateway

The following Flexi Classic gateway can be used for PROFINET IO: UE410

F

EN4.

The GSD file is available on www.sick.com.
The UE410

F

EN4 supports:

PROFINET IO conformance class A
LLDP
SNMP
MIB II
fast integrated switching
auto-MDI
auto negotiation
cyclic IO communication
acyclic communication
diagnostic alarms

10.1

Interfaces and operation

The UE410-EN is equipped with four digital control outputs X1–X4.
The UE410-EN is equipped with an integrated 3-port switch for connection with the Ether-
net network. Two RJ45 sockets are available for the connection. The switch functionality
allows the UE410-EN to be used for connection to another Ethernet component (e.g. con-
nection to a notebook) without having to interrupt the Ethernet connection to the network.

Fig. 20: Interfaces and
display elements of the
UE410-EN

Terminals of digital control
outputs X1–X4

RJ45 Ethernet socket

RJ45 Ethernet socket

LED power supply (green)

LED network activity for
Ethernet port 1 or 2 (green)

LED Error (red/green)

«
...
120
121
122
123
124
...
»

Summary of Contents for Flexi Classic





























































































































































Reviews:

No comments

Related manuals for Flexi Classic

Brand: Particle Pages: 6

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

Brand: Icom Pages: 30

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ray Pages: 11

M16/RM N.C. DN 65 EEX

Brand: Madas Pages: 44

Brand: Pando Pages: 43

Brand: Fingertips Lab Pages: 15

Brand: WAGNER Pages: 60

Brand: Parker Pages: 16

Brand: ZKTeco Pages: 2

Brand: Vag Pages: 12

Brand: Fancom Pages: 23

Brand: Beninca Pages: 7

Brand: TFK Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands