SICK Flexi Classic Operating Instructions Manual Download Page 115

Page: 115 / 156

Operating Instructions

Chapter

Flexi Classic Gateways

8011834/YT28/2016-03-15

115

Subject to change without notice

EtherNet/IP Gateway

9.8

Resetting to factory settings

The UE410-EN can be reset to the factory settings as follows:

Open a web browser on a PC in the same network and go to the address of the
UE410

EN. The following web page is displayed:

Click the reboot button. The following web page is displayed:

Activate

Set configuration for PLC Interface and Data Sets to factory default settings

Click the button

Yes: Reboot

. The following web page is displayed:

The UE410-EN is reset to the factory settings. The web server of the UE410-EN is called up
again automatically.

Summary of Contents for Flexi Classic





























































































































































Search results

Summary of Contents for Flexi Classic

Reviews:

Related manuals for Flexi Classic

Brands by name

Popular brands

SICK Flexi Classic, Operating Instructions Manual

Search results

Summary of Contents for Flexi Classic

Reviews:

Related manuals for Flexi Classic

Brands by name

Popular brands