SICK Flexi Classic Operating Instructions Manual Download Page 58 | Manualshive

Page: 58 / 156

background image

Chapter

7

Operating Instructions

Flexi Classic Gateways

58

© SICK AG • Industrial Safety Systems • Germany • All rights reserved

8011834/YT28/2016-03-15

Subject to change without notice

Modbus/TCP Ethernet Gateway

7.3.2

Operating modes in the transfer mode Tx (From PLC)

Slave (PLC writes) — PLC sends digital output data to the UE410-EN3

In this operating mode the PLC sends writing requirements as master to the UE410-EN3 in
order to set the digital outputs. If this operating mode is desired:

Chose the operating mode

Slave (PLC Writes)

in the

Tx (From PLC) Transfer Mode

selection field. All the further settings do not apply.
Activate

Save in Flash

and click

Submit

to save the selection.

Only if

Save in Flash

is checked, will the new configuration be stored in the UE410-EN3’s

non-volatile memory and be available after a restart of the gateway.

Submit

without

checking

Save in Flash

allows, for example, the testing of new configurations without

overwriting the old configuration.
UE410-EN3 as slave — addressing the digital outputs:

Unit ID

1

Address
(Base 1)

Description

Access

Scope
(words)

1800 Digital

outputs

Set/Get 1

Master (Poll the PLC) — UE410-EN3 requests the data from the PLC.

In this operating mode the UE410-EN3 as master requests the data continuously from the
PLC in order to set the digital output settings. If this operating mode is desired:

Select the operating mode

Master (Poll the PLC)

in the

Tx (From PLC) Transfer Mode

selection field.
Carry out the following settings on the same web page (see Tab. 63 on page 55):
– PLC IP Address
– PLC Device ID
– Digital Output Polling Enable
– Digital Output Setting PLC Address
– Digital Output Setting Polling Rate
Activate

Save in Flash

and click

Submit

to save the selection.

Only if

Save in Flash

is checked, will the new configuration be stored in the UE410-EN3’s

non-volatile memory and be available after a restart of the gateway.

Submit

without

checking

Save in Flash

allows, for example, the testing of new configurations without

overwriting the old configuration.

7.3.3

Modbus commands and error messages

The UE410-EN3 supports the following Modbus commands and error messages:

Modbus command

Value

Read Holding Registers

3

Write Multiple Registers

16 (10hex)

Read/Write Multiple Registers

23 (17hex)

Note

Tab. 65: Data addressing of
the UE410-EN3 digital

outputs

Note

Tab. 66: Modbus commands

«
...
56
57
58
59
60
...
»

Summary of Contents for Flexi Classic





























































































































































Reviews:

No comments

Related manuals for Flexi Classic

Brand: YASKAWA Pages: 256

Brand: Baby Trend Pages: 8

Brand: Baby Trend Pages: 19

Brand: Baby Trend Pages: 5

Brand: Baby Trend Pages: 4

TEMP2000 Series

Brand: Samwontech Pages: 91

Brand: Warren rupp Pages: 18

Brand: Yamaha Pages: 100

Brand: Taco Electronic Solutions Pages: 28

Brand: U-Prox Pages: 3

Brand: U-Prox Pages: 25

Brand: U-Prox Pages: 2

Brand: cinetto Pages: 56

Brand: Daihan Scientific Pages: 11

Brand: Sven Pages: 6

Brand: GE Pages: 32

SYSVRF AHU 10HP S

Brand: SystemAir Pages: 16

Brand: Zapi Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands