manualshive.com logo in svg

SICK Flexi Classic, Operating Instructions Manual, Page: 95 / 156

Share
Download
SICK Flexi Classic Operating Instructions Manual Download Page 95

Operating Instructions 

Chapter 

9

Flexi Classic Gateways

 

8011834/YT28/2016-03-15 

© SICK AG • Industrial Safety Systems • Germany • All rights reserved 

95 

Subject to change without notice 

EtherNet/IP Gateway 

9.4

 

Configuration of the interface to the PLC — how the 

data are transferred 

The configuration steps in this section specify how the data on the higher-level PLC are 
transferred. Different operating modes can be selected to this purpose. The number of 
possible connections to the PLC depends on whether the UE410-EN1 is operated as a 
master or slave. Depending on the setting, up to 128 PLCs can address the UE410-EN1 at 
the same time. 

Operating mode of the UE410-EN 

Maximum connections 

Rx (To PLC) Transfer Mode: Write-to-Tag/File 
Tx (From PLC) Transfer Mode: Read-from-Tag/File 

Rx and Tx: 1 

Rx (To PLC) Transfer Mode: Write-to-Tag/File 
Tx (From PLC) Transfer Mode: PLC Writes 

Rx: 1 
Tx: 127 

Rx (To PLC) Transfer Mode: Polling 
Tx (From PLC) Transfer Mode: Read-from-Tag/File 

Rx: 127 
Tx: 1 

Rx (To PLC) Transfer Mode: Polling 
Tx (From PLC) Transfer Mode: PLC Writes 

Rx and Tx: 128 

Open a web browser on a PC in the network and go to the address of the UE410-EN. 
Click 

PLC Interface Configuration

 on the UE410-EN homepage. The following web page 

is displayed: 

The page shows the current settings of the interface to the PLC. 

Tab. 89: Number of possible 
connections 

Summary of Contents for Flexi Classic





























































































































































Reviews:

No comments