manualshive.com logo in svg

SICK Flexi Classic, Operating Instructions Manual

Share
Download
SICK Flexi Classic Operating Instructions Manual Download Page 59

Operating Instructions 

Chapter 

7

Flexi Classic Gateways

 

8011834/YT28/2016-03-15 

© SICK AG • Industrial Safety Systems • Germany • All rights reserved 

59 

Subject to change without notice 

Modbus/TCP Ethernet Gateway

Modbus error response 

Description 

1 Illegal Function 

The requested function is not supported. 

2 Illegal Data Address 

Undefined data address received. 

3 Illegal Data Value 

Request with illegal data values, for example not enough data 
requested for a data set. 

10 Gateway Paths Not Available 

Invalid configuration, for example polling or setting of the digital 
outputs via PLC during operation of the UE410-EN3 in master 
mode. 

7.4

 

Configuration of the gateway — which data are 

transferred 

The UE410-EN3 processes the data of a UE410-EN3 Flexi Classic system and makes them 
available in different compilations, the data sets for the PLC.  
The configuration steps in this section are used to define which data sets are transferred 
to the higher-level PLC. There are 6 data sets available to this purpose: Data sets 1-5 
contain fixed data compilations, Data set 6 can be configured by the user. The data sets 
that are to be transferred to the PLC must be activated. 

Open a web browser on a PC in the network and go to the address of the UE410-EN3. 
Click 

Flexi System Interface Configuration

 on the UE410-EN3 homepage. The 

following web page is displayed: 

Tab. 67: Modbus error 
messages 

Summary of Contents for Flexi Classic





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands