manualshive.com logo in svg

SICK Flexi Classic, Operating Instructions Manual, Page: 140 / 156

Share
Download
SICK Flexi Classic Operating Instructions Manual Download Page 140

Chapter 

10

 

Operating Instructions 

Flexi Classic Gateways

 

140

 

© SICK AG • Industrial Safety Systems • Germany • All rights reserved 

8011834/YT28/2016-03-15 

Subject to change without notice 

PROFINET IO Gateway 

10.6

 

Resetting to factory settings 

The UE410-EN can be reset to the factory settings as follows: 

Open a web browser on a PC in the same network and go to the address of the 
UE410

F

EN. The following web page is displayed: 

Click the reboot button. The following web page is displayed: 

Activate 

Set configuration for PLC Interface and Data Sets to factory default settings

.

Click the button 

Yes: Reboot

. The following web page is displayed: 

The UE410-EN is reset to the factory settings. The web server of the UE410-EN is called up 
again automatically. 

Summary of Contents for Flexi Classic





























































































































































Reviews:

No comments