SICK Flexi Classic Operating Instructions Manual Download Page 72

Page: 72 / 156

Chapter

Operating Instructions

Flexi Classic Gateways

8011834/YT28/2016-03-15

Subject to change without notice

Ethernet TCP/IP Gateway

LED

Meaning

No power supply

PWR

Green

Power supply switched on

No Ethernet connection

Green

Ethernet connection active, no data transmission

LINK/ACT 1
LINK/ACT 2

Green

Ethernet connection active, data transmission

No power supply

ERR

Green

Gateway operating, no error message, at least one
Ethernet connection exists

Green

Gateway operating, valid IP address assigned, configu-
ration is valid, but no Ethernet connection established.
All data sets are deactivated

Red

No flex bus communication

Red

Internal device error

Red/Green Self-test of the gateway after switching on the power

supply on the Flexi Classic system

Symbol description:

LED off

Green: LED lights up green

Red: LED flashes red

Error elimination is described in section “Troubleshooting” below.

8.2

Basic configuration — assigning an IP address

Configuration of the UE410-EN is performed browser-supported via the integrated web
server of the gateway.

Ensure that the UE410-EN is installed correctly, energised and connected with the
Ethernet network.
Open a web browser on a PC in the same network and go to the address of the
UE410

EN. Upon delivery, the UE410-EN is configured for the following address:

– IP address 192.168.250.250
– Subnet mask 255.255.0.0
– Default gateway 0.0.0.0
The following web page is displayed:

Tab. 72: Meaning of the LED
displays

Note

Summary of Contents for Flexi Classic





























































































































































Search results

Summary of Contents for Flexi Classic

Reviews:

Related manuals for Flexi Classic

Brands by name

Popular brands

SICK Flexi Classic, Operating Instructions Manual

Search results

Summary of Contents for Flexi Classic

Reviews:

Related manuals for Flexi Classic

Brands by name

Popular brands