manualshive.com logo in svg

SICK Flexi Classic, Operating Instructions Manual

Share
Download
SICK Flexi Classic Operating Instructions Manual Download Page 48

Chapter 

6

Operating Instructions 

Flexi Classic Gateways

 

48

 

© SICK AG • Industrial Safety Systems • Germany • All rights reserved 

8011834/YT28/2016-03-15 

Subject to change without notice 

DeviceNet Gateway 

Display 

Meaning 

PWR (green) 

Supply voltage present 

NS (off) 

“DUP MAC Check” not completed successfully. 

NS (green flashing) 

UE410-DEV operating on the bus, but has not yet been detected by a 
master or no logical connection has been established to the UE410-

DEV. 

NS (green) 

UE410-DEV has been detected by a master and a logical connection 
has been established to the UE410-DEV. 

NS (red) 

During “DUP MAC Check”, UE410-DEV has found a different device 
with the same MAC ID. 

MS (green flashing)

 

The fieldbus connection has been interrupted. The remote PLC is in 
the stop mode. The master is currently attempting to establish the 

connection to the UE410-DEV. The planned I/O size in the scan list is 
incorrect (Error 77 on the scanner). 

MS (green) 

UE410-DEV is ready and the PLC is in the Run mode. 

MS (red flashing)

 

The internal EEPROM has an error. 

Display 

Meaning 

X 10 

Address switch 1 (possible bus addresses 0-63)  
10-position rotary switch for setting the module address (tens) 

X 1

Address switch 2 (possible bus addresses 0-63)  
10-position rotary switch for setting the module address (units) 

DIP switch 

4-pole DIP switch for setting the baud rate  
DIP 3 and 4 are not used.  
If a larger address is selected, address 63 is active. 

The occurrence of random or systematic errors in the gateway or in its operation does 
not result in the degradation of the safety functions on the Flexi Classic system. 
With the operating voltage switched on, no gateways are allowed to be disconnected 
from the Flexi Classic system or added by plugging in. 
The DeviceNet master cannot overwrite the address set. 
A modified address setting only becomes effective after switching off and switching on 
the Flexi Classic system. 

6.1.3

 

Application diagnostic outputs UE410-DEV 

Assignment 

Description 

X1-X4

 

Short circuit and overload detecting control outputs (PNP) supplied via Flexi 
Classic system 

Tab. 56: Indication LED 
UE410-DEV 

Tab. 57: Address switch 
UE410-DEV 

Notes 

Tab. 58: Application 
diagnostic outputs 

Summary of Contents for Flexi Classic





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands