manualshive.com logo in svg

SICK Flexi Classic, Operating Instructions Manual

Share
Download
SICK Flexi Classic Operating Instructions Manual Download Page 31

Operating Instructions 

Chapter 

4

Flexi Classic Gateways

 

8011834/YT28/2016-03-15 

© SICK AG • Industrial Safety Systems • Germany • All rights reserved 

31 

Subject to change without notice 

PROFIBUS DP Gateway 

Design variant 4 is shown in the following table. 

Data direction 

I/O modules

 

GSD identifier 

Read 

Write 

CRC1 DIG-OUT 

CRC2 REQ-ID 

BAS1 Reserved 

SCB1 Basic1 4 Byte in/out 

Contains configuration checksum 
and basic diagnostics 

ID: 33h (mandatory) 

BAS2 Reserved 

BAS3 – 

SCB2 Basic2 2 Byte in 
Contains extended basic diagnostics

ID: 11h (optional) 

BAS4 – 

B1 – 

B2 – 

:

:

DIAG 10 Byte in 
Depending on the REQ-ID this 

module contains 
10 bytes diagnostics with varying 
content 

ID: 19h (optional) 

B10 – 

MED1 – 

MED2 – 

:

:

MED 13 Byte 
Contains the input signals for all Flexi 
Classic modules fitted 
E.g. MED7 contains the input data 
for module 7 

ID: 1Ch (optional) 

MED13 – 

See also section 3.2 “Status information of all Flexi Classic gateways (system bytes)”. 

 

If a DP master is used that does not send any planning data to the UE410-PRO (e.g. 
PROFIBUS Master Simulator PR-MSV01 (6022458) from SICK in the “Start without GSD 
file” mode), the UE410-PRO supplies the diagnostic data as for plan 5 (see Tab. 34 on 
page 30). 

4.2.2

 

Documenting with PROFIBUS-DP Master Simulator 

You can save diagnostics data on a PC with the aid of the PROFIBUS-DP Master Simulator 
(see section 11.7 “Accessories/spare parts”) and the file flexi_config_list.xls. 
For this purpose, connect a data cable between PC, PROFIBUS-DP Master Simulator and 
UE410-PRO (RS-232-D-Sub). Install the file “flexi_config_list.xls” on your PC, Excel 2000 or 
later must be installed on the PC.  
You can then save and document the diagnostics data and settings for the overall system 
with the aid of your PC. 
We also refer you to our homepage on the Internet at 

http://www.ue410flexi.com 

There you will find the following files for download: 

GSD file 
flexi_config_list.xls  

4.2.3

 

Diagnostics data UE410-PRO 

You will find the description of the status bytes in the section “Status information of all 
Flexi Classic gateways (system bytes)”. 

Tab. 35: Format of the diag-
nostics data UE410-PRO 

Summary of Contents for Flexi Classic





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands