Reichhardt ULTRA GUIDANCE PSR ISO Page 119 Operator'S Manual Download

Page: 119 / 132

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

PAGE 119

CHAPTER

TROUBLESHOOTING

Fehler-Nr.:

Description

Cause

Troubleshooting

1104

TAC sensor 2 left open wire.

- TAC sensor is defective.

- Visual control of TAC sensor.

- Open wire in cable.

- Check the cables from PSR iBox to the

TAC sensor.

- Contacts of connectors are

opened.

- Check contacts of connectors.

1105

TAC sensor 2 left short

circuit.

- TAC sensor is defective.

- Visual control of TAC sensor.

- Short circuit in cable.

- Check the cables from PSR iBox to the

TAC sensor.

- Contacts of connectors are closed.

- Check contacts of connectors.

1106

TAC sensor 2 right open

wires.

- TAC sensor is defective.

- Visual control of TAC sensor.

- Open wire in cable.

- check the cables from PSR iBox to the

TAC sensor.

- Contacts of connectors are

opened.

- Check contacts of connectors.

1107

TAC sensor 2 right short

circuit.

- TAC sensor is defective.

- Visual control of TAC sensor.

- Short circuit in cable.

- Check the cables from PSR iBox to the

TAC sensor.

- Contacts of connectors are closed.

- Check contacts of connectors.

1150

Rowfeeler open wire.

- Rowfeeler is defective.

- Visual control of rowfeeler.

- Open wire in cable.

- Check cables from PSR iBox to

rowfeeler.

- Contacts of connectors are

opened.

- Check contacts of connectors.

1151

Rowfeeler short circuit.

- Rowfeeler is defective.

- Visual control of rowfeeler.

- Short circuit in cable.

- Check cables from PSR iBox to

rowfeeler.

- Contacts of connectors are closed.

- Check contacts of connectors.

1200

Camera no reaction.

- Camera is defective.

- Visual control of camera.

- Open wire in cable.

- Check cables from PSR iBox to camera.

- Contacts of connectors are

opened.

- Check contacts of connectors.

1210

No signal from camera

while operating.

- Camera is defective.

- Visual control of camera.

- Open wire in cable.

- Check cables from PSR iBox to camera.

- Contacts of connectors are

opened.

- Check contacts of connectors.

1220

No valid signals from

camera.

- Adjustment of camera is incorrect.

- Check mounting of the camera.

- Distance between camera and

plants is too small.

- Check parameters/adjustments of the

camera.

- There’s excess vegetation between

plantrows.

- Clean camera lens.
- Use additional lighting when ambient

lighting is poor.

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands