Reichhardt ULTRA GUIDANCE PSR ISO Page 9 Operator'S Manual Download

Page: 9 / 132

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

PAGE 9

CHAPTER SAFET Y

1. Safety

1.1.

Intended use

This automatic steering system is designed to be controlled by persons working in agriculture or forestry

including special cultures like vineyards, fruit trees, or vegetables. Any usage beyond recommendations is

therefore prohibited. ULTRA GUIDANCE PSR ISO is not suitable for applications on narrow dikes or steep

hillsides, when danger of vehicle roll-over exists. It should not be exposed to areas that are in danger of

explosions. Never expose the unit or individual components to chemicals such as: acids, lye, oils, lubricants

or other aggressive petro-chemical materials. The manufacturer is not responsible for any damages relating to

non-purpose oriented usage. The risk is the sole responsibility of the user. These purpose oriented conditions

also apply to recommended operator regulations as well as service and maintenance directions.

1.2.

General advice

Please read this manual thoroughly.

This steering system is fabricated under respected technical regulations and

expertly installed. In this manual you receive all the information required for proper operation and maintenance

of the system. Please observe all reference points and directions exactly. Failure to do so could lead to personal

injury or equipment damage. This manual and safety decals may also be available in other languages. Check

with your dealer or our internet website.

This manual is considered a permanent part of the steering system

and shall remain with the steering system in

the event that it is sold to other parties.

Measurements

in this manual are given in US Standard. Make sure to use correct tools.

If original brackets or parts are not used, it could potentially lead to injury or material damage caused by

malfunction of the steering system. Therefore, always use approved brackets and spare parts.

1.2.1. Responsibilities of the owner

Only persons who have read and understood the complete manual should work with this system.

Only persons which are comfortable with installation, service and repair of the steering system,and also aware

of possible dangers in conjunction with the job, should use the system.

Regional regulations for health protection and accident prevention must be obeyed at all times and while

working with the system. Never use the system on public roads or highways.

Any changes to the steering system which are not authorized by the manufacturer, void any liability of the

manufacturer in the event of a malfunction.

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands