Reichhardt ULTRA GUIDANCE PSR ISO Page 4 Operator'S Manual Download

Page: 4 / 132

PAGE 4

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

TABLE OF CONTENTS

4. Operation ............................................................................................................23

4.1.

Operating interface ISOBUS terminal ....................................................................23

4.1.1.

Function of the buttons ..........................................................................................23

4.1.2.

Function keys ..........................................................................................................23

4.2.

On and off switch of ULTRA GUIDANCE PSR ISO ..................................................25

4.3.

Activation and Deactivation of ULTRA GUIDANCE PSR ISO ..................................25

4.4.

Main screen.............................................................................................................26

4.5.

Select drive mode ...................................................................................................26

4.5.1.

Automatic Drive modes ..........................................................................................27

4.5.2.

Drive mode manual ................................................................................................28

4.6.

Reaction setting ......................................................................................................29

4.7.

Spacing setting .......................................................................................................30

4.8.

Menu structure .......................................................................................................31

4.9.

Main Menu ..............................................................................................................32

4.9.1.

ISOBUS terminal settings .......................................................................................33

4.9.2.

Computer Setting ....................................................................................................35

4.9.3.

Set measurements .................................................................................................36

4.9.4.

Setting the GPS receiver.........................................................................................37

4.9.5.

Teach-In Menu .........................................................................................................43

4.9.6. Diagnostic ................................................................................................................ 51
4.9.7.

System Information .................................................................................................54

4.9.8.

Service menu ..........................................................................................................55

4.9.9. Calculator ................................................................................................................56
4.10.

Setting parameters – Adjusting values ................................................................57

4.10.1.

Acceptance of values ..............................................................................................58

4.11.

Numerical entry.......................................................................................................59

4.12.

Saving changes .......................................................................................................59

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands