Reichhardt ULTRA GUIDANCE PSR ISO Page 36 Operator'S Manual Download

Page: 36 / 132

PAGE 36

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

CHAPTER

OPERATION

4.9.3. Set measurements

ULTRA GUIDANCE PSR ISO can store settings of up to eight different

vehicles. All vehicle settings will be stored under one number.

When switching the PSR iBox to another vehicle, choose the vehicle

number under which the stored information is found.

Choose

and confirm the selection.

Press the function keys

to select the required vehicle

number.

Press and hold the function key

until the stored symbol

appears. Proceed as described in chapter 4.12.

Picture 42:

Set vehicle number

Picture 43:

Selection of vehicle number

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands