Reichhardt ULTRA GUIDANCE PSR ISO Operator'S Manual Download

Page: 50 / 132

PAGE 50

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

CHAPTER

OPERATION

Calibrating the tilt sensor

When using a tilt sensor, its zero position must be calibrated.

Choose

and confirm the selection.

Advice!

Calibrate the vehicle on an even surface to ob-

tain the most precise possible results.

A flashing “1” will now appear on the display. Select the wheel

position on the ground. Confirm this position by pressing the

function key

Turn the vehicle by 180° and place the wheels exactly on the

previously selected wheel positions.

A flashing “2” will now appear on the display. Confirm this position

by pressing the function key

. Proceed as described in

chapter 4.12.

Picture 72:

Selecting Calibrate tilt sensor

Picture 73:

Calibrating position 1

Picture 74:

Calibrating position 2

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands