Reichhardt ULTRA GUIDANCE PSR ISO Operator'S Manual Download

Page: 121 / 132

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

PAGE 121

KAPITEL

TROUBLESHOOTING

Error-No.:

Description

Cause

Troubleshooting

1413

Ultra sonic 4 no signal.

- Object outside detection area.

- Visual control of ultra sonic 4.
- Check sensor position.

1414

All ultra sonic no signal.

- Object outside detection area of all

sensors.

- Check sensor positions.

1500

Lock valve left open wire.

- Lock valve is defective.

- Visual control of lock valve.

- Open wire in cable.

- Check the cables from PSR iBox to the

lock valve.

- Contacts of connectors are opened.

- Check contacts of connectors.

1501

Lock valve left short circuit.

- Lock valve is defective.

- Visual control of lock valve.

- Short circuit in cable.

- Check the cables from PSR iBox to the

lock valve.

- Contacts of connectors are closed.

- Check contacts of connectors.

1502

Lock valve right open wire.

- Lock valve is defective.

- visual control of lock valve.

- open wire in cable.

- check the cables from PSR iBox to the

lock valve.

- contacts of connectors are opened.

- check contacts of connectors.

1503

Lock valve right short

circuit.

- Lock valve is defective.

- Visual control of lock valve.

- Short circuit in cable.

- Check the cables from PSR iBox to the

lock valve.

- Contacts of connectors are closed.

- Check contacts of connectors.

1550

Steer valve left open wire.

- Steer valve is defective.

- Visual control of steer valve.

- Open wire in cable.

- Check cables from PSR iBox to steer

valve.

- Contacts of connectors are opened.

- Check contacts of connectors.

1551

Steer valve left short circuit.

- Steer valve is defective.

- Visual control of steer valve.

- Short circuit in cable.

- Check cables from PSR iBox to steer

valve.

- Contacts of connectors are closed.

- Check contacts of connectors.

1552

Steer valve right open wire.

- Steer valve is defective.

- Visual control of steer valve.

- Open wire in cable.

- Check cables from PSR iBox to steer

valve.

- Contacts of connectors are opened.

- Check contacts of connectors.

1553

Steer valve right short

circuit.

- Steer valve is defective.

- Visual control of steer valve.

- Short circuit in cable.

- Check cables from PSR iBox to steer

valve.

- Contacts of connectors are closed.

- Check contacts of connectors.

1700

Front plug no voltage.

- Outlet at the PSR iBox is defective.

- Check cables from PSR iBox to front

plug box.

- Short circuit in cable.

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands