Reichhardt ULTRA GUIDANCE PSR ISO Operator'S Manual Download

Page: 103 / 132

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

PAGE 103

CHAPTER

PSR TAC

7.4.

Main menu PSR TAC

Display:

Main screen

Tap the function key

to change to the main menu PSR TAC.

7.4.1. TAC sensor calibration

Choose

and confirm the selection.

To get consistently good results with the TAC sensor, it is advised

re-calibrate it occasionally. Especially during initial use or after

lengthy periods of no use.

Make sure the plastic wand is in rest position. It should not touch

anything or be moved by any action. Do not touch the sensor. The

value should be between 40 and 70.

Press and hold the function key

until the stored symbol

appears. Proceed as described in chapter 4.12.

Advice!

For more consistent results, the vehicle may

have two sets of sensors. When pressing the function

keys

the operator will first see S1 then S2

then S3 and S4. All sensors will be calibrated together.

Picture 179:

Main screen PSR TAC

Picture 180:

Select TAC sensor

Picture 181:

Calibrate TAC sensor

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands