manualshive.com logo in svg

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Share
Download
Reichhardt ULTRA GUIDANCE PSR ISO Operator'S Manual Download Page 47

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO 

PAGE 47

CHAPTER 

OPERATION

Entering the speed manually

Here you can set the speed between the tractor meter and ULTRA 

GUIDANCE PSR ISO manually.

Choose 

 and confirm the selection.

Now you can set the differential speed between the ULTRA 

GUIDANCE PSR ISO and the tractor meter so that they agree with 

each other. 

Press the function keys 

,

 to set the speed pulses.

Alternatively, you can also set the values manually as described 

in chapter 4.11.

Advice!

 To check the set increments, drive the vehicle 

keeping your speed as closely as possible to 3 mph. 

Compare the driving speed of the vehicle with the speed 

indicated on the display.

If the speed indicated on the display is too high, increase 

the speed increments.

If the speed indicated on the display is too low, decrease 

the speed increments.

Check the different driving speeds.

Press and hold the function key 

 until the stored symbol 

appears. Proceed as described in chapter 4.12.

Picture 64:

Manual speed selection

Picture 65:

Setting the speed manually

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands