Reichhardt ULTRA GUIDANCE PSR ISO Page 46 Operator'S Manual Download

Page: 46 / 132

PAGE 46

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

CHAPTER

OPERATION

Advice!

If the speed signal from the vehicle/radar sensor

is used, the increments must also be set.

If the current speed is being detected by the GPS receiver

or ISO bus 11783, the menu will switch directly to the

selection menu for the speed signals.

Automatic speed calibration

In order to calibrate the speed between the tractor meter and

ULTRA GUIDANCE PSR ISO automatically, a distance of exactly

328 ft must be driven.

Choose

and confirm the selection.

Choose

and confirm the selection.

Now drive for a distance of exactly 328 ft.

Choose

and confirm the selection. Proceed as described

in chapter 4.12.

Advice!

Check the taught speed calibration in the menu

“Manual entry of speed increments”

and correct the speed

calibration if necessary.

Picture 61:

Calibrating speed automatically

Picture 62:

Automatic speed Start

Picture 63:

Automatic speed Stop

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands