background image

PAGE 40 

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

CHAPTER 

OPERATION

General RGS receiver settings

Choose 

 and confirm the selection.

In this menu general settings for the GPS receiver are made. You 

can make the following settings:

• 

NP    : number of decimal places, 5 - 7 possible.

• 

Appl   :  Shift application. Depends on GPS receiver, e.g. RTK 

<-> WAAS/EGNOS

• 

PRN 1: Reference satellite 1

• 

PRN 2: Reference satellite 2

• 

Diff    : Difference mode. Depends on GPS receiver.

Press the function keys 

,

 to select the desired setting.

Tap the function key 

 to change the setting.

Press and hold the function key 

 until the stored symbol 

appears. Proceed as described in chapter 4.12.

Advice!

 The setting for “NP” always should be set to 7. 

This way you receive the highest accuracy for the 

positioning of the GPS receiver.

Advice!

 PRN 1 and PRN 2 must always be set identically.

Picture 50:

Selecting general RGS receiver settings

Picture 51:

General RGS receiver settings

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Reviews: