Reichhardt ULTRA GUIDANCE PSR ISO Operator'S Manual Download

Page: 30 / 132

PAGE 30

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

CHAPTER

OPERATION

4.7.

Spacing setting

Display:

Main screen

Spacing identifies the distance of the machine to the default line.

The setting of these values are needed to allow the implement to

continue to seamlessly work lines.

Press the function key

until the symbol flashes.

Pressing the function keys

sets the distance. The

range of settings is b 12 and + 35 inches for the distance

to the crop edge. Or between -20 and +20 inches for the distance

to the center of the vehicle. The setting information will be stored

with the actual drive mode in the system.

Advice!

Pressing the function keys

will disengage the steering system when changing the

spacing setting.

Tap the function key

to store the spacing level.

Picture 30:

Drive mode with center offset

Picture 31:

Drive mode with distance to the crop edge

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands