Reichhardt ULTRA GUIDANCE PSR ISO Page 92 Operator'S Manual Download

Page: 92 / 132

PAGE 92

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

CHAPTER

PSR SONIC

6.4.

Main Menu PSR SONIC

Display:

Main screen

Tap the function key

to change to the main menu PSR

SONIC.

6.4.1. Sample Spacing SONIC

With the sample spacing of the SONIC sensors, the operator can

adjust how aggressive the steering correction should be when a

deviation from the intended line is recognized.

Choose

and confirm the selection.

Advice!

This setting is meant for all PSR SONIC drive

modes.

Choose

uand press the function key

until the save screen shows. Proceed as described in chapter 4.12.

= weak sample spacing. The vehicle reacts slower to a

deviation.

= normal sample spacing. The vehicle reacts normally

to a deviation.

= high sample spacing. The vehicle reacts even to the

slightest deviations.

Picture 152:

Main Menu PSR SONIC

Picture 153:

Setting of Sensor Sample Spacing

Picture 154:

Selection of sample spacing

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands