Reichhardt ULTRA GUIDANCE PSR ISO Operator'S Manual Download

Page: 25 / 132

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

PAGE 25

CHAPTER

OPERATION

4.2.

On and off switch of ULTRA GUIDANCE PSR ISO

By pressing the main switch ULTRA GUIDANCE PSR ISO is activated.

Depending on the vehicle an applicable main switch is installed.

Please ask the service technician where the main switch was

installed.

Read the safety instructions and confirm by pressing the Enter

key

Attention!

ULTRA GUIDANCE PSR ISO has to be turned

OFF at the end of field work and before entering public

roads by the main switch.

4.3.

Activation and Deactivation of ULTRA GUIDANCE PSR ISO

By the displayed symbol of the function key

you see the current

status of the steering system. The symbol

shows, that ULTRA

GUIDANCE PSR ISO is active. If you see symbol

PSR ISO

TOP is deactivated.

Activating ULTRA GUIDANCE PSR ISO:

The system can only be activated when the main screen is on.

•

By pressing the function key

•

By activating the foot switch.

•

By the menu TL-TOP.

Deactivating ULTRA GUIDANCE PSR ISO:

•

By pressing the function key

•

By the menu TL-TOP.

•

By activating the foot switch.

•

By switching the main switch ON/OFF.

•

By manually moving the steering wheel.

The system will deactivate automatically:

•

When driving speed is too high.

•

When experiencing a system malfunction.

•

When opening the cab door or leaving the drivers seat (if

activated at set up).

Picture 21:

Safety information

Picture 22:

Main screen (steering activated)

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands