Reichhardt ULTRA GUIDANCE PSR ISO Operator'S Manual Download

Page: 97 / 132

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

PAGE 97

CHAPTER

PSR SONIC

6.6.4. Crop Edge

Display:

Main screen

Set drive mode according to the adjoined picture (see chapter

4.5.).

Tap the function key

to switch between left and right crop

edge.

Advice!

In the drive mode crop edge the distance shown

is the medium distance between the left

or right

sensor pair to the crop edge.

Set sensors:

Set sensors according to adjacent pictures. Pay attention that the

outer sensor hits the upper third and the inner sensor hits the

lower third of the crop edge.

Picture 168:

Main Screen Crop Edge

Picture 170:

Sensor direction right crop edge

Picture 169:

Sensor direction left crop edge

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands