Reichhardt ULTRA GUIDANCE PSR ISO Page 118 Operator'S Manual Download

Page: 118 / 132

PAGE 118

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

CHAPTER

TROUBLESHOOTING

Error-No.:

Description

Cause

Troubleshooting

1080

Gyroscope open wire.

- Gyroscope is defective.

- Visual control of gyroscope.

- Open wire in cable.

- Check the cables from PSR iBox to the

gyroscope.

- Contacts of connectors are

opened.

- Check contacts of connectors.

1081

Gyroscope short circuit.

- Gyroscope is defective.

- Visual control of gyroscope.

- Short circuit in cable.

- Check the cables from PSR iBox to the

gyroscope.

- Contacts of connectors are closed.

- Check contacts of connectors.

1082

Gyroscope no reaction.

- Gyroscope is defective.

- Visual control of gyroscope.
- Check the cables from PSR iBox to the

gyroscope.

- Check contacts of connectors.
- Check analog value in diagnostic menu.

1084

Gyroscope value not in valid

range.

- Too sharp a turn with too high

speed.

- See 1082.
- Reduce speed.
- Make wider turn.

1085

Gyroscope average value is

out of range.

- Speed signal is defective.

- See 1082.

- Gyroscope is defective.

1086

Constant speed is not

allowed together with

gyroscope.

- Constant speed is set in the

system.

- Manual speed entry needs to be

adjusted by a service technician.

1100

TAC sensor left open wire.

- TAC sensor is defective.

- Visual control of TAC sensor.

- Open wire in cable.

- Check the cables from PSR iBox to the

TAC sensor.

- Contacts of connectors are

opened.

- Check contacts of connectors.

1101

TAC sensor left short circuit.

- TAC sensor is defective.

- Visual control of TAC sensor.

- Short circuit in cable.

- Check the cables from PSR iBox to the

TAC sensor.

- Contacts of connectors are closed.

- Check contacts of connectors.

1102

TAC sensor right open wire.

- TAC sensor is defective.

- Visual control of TAC sensor.

- Open wire in cable.

- Check the cables from PSR iBox to the

TAC sensor.

- Contacts of connectors are

opened.

- Check contacts of connectors.

1103

TAC sensor right short

circuit.

- TAC sensor is defective.

- Visual control of TAC sensor.

- Short circuit in cable.

- Check the cables from PSR iBox to the

TAC sensor.

- Contacts of connectors are closed.

- Check contacts of connectors.

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands