Reichhardt ULTRA GUIDANCE PSR ISO Page 127 Operator'S Manual Download

Page: 127 / 132

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

PAGE 127

CHAPTER

TRADE TERMS AND ABBREVIATIONS

Term

Abbreviation

Description

Satellite supported position signals

GPS

24 earth circling satellites send GEO-positioned

signals to earth bound receivers.

Accuracy

Accuracy of a certain position which can be

relocated within 24 hours.

Correction signal

DGPS

A correction signal which corrects inaccuracies

like time deviation, ion spherical tensions or

GPS system malfunctions.

Wide Area Augmentation System

WAAS

Correction signal US Gov.

European Geo-Stationary Navigation

Overlay System

EGNOS

Correction signal for Europe and West Russia.

Beacon

Low cost correction signal. Check availability.

Omnistar

Low cost correction signal. Check availability.

Real Time Kinematics Correction

Signal

RTK

Correction signal available through a base

station.

Baud

Transmission speed.

National Marine Electronics

Association

NMEA 0183

NMEA 0183 is a standard protocol used by GPS

receivers to transmit data.

Recommended Minimum Specific

Global Navigation Satellite Support

Data

GPRMC

Part of the NMEA 0183 protocol.

Global Positioning System Fit Data

GPGGA

Part of the NMEA 0183 protocol.

Parameter

Fixed value

Port

Serial interface

CAN BUS

data bus

Slip

Ratio of the speed of a driven wheel to that of a

non-driven co-rotating wheel.

11. Trade Terms and Abbreviations

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands