PRÜFTECHNIK VIBSCANNER VIB 5.400 Operating Instructions Manual Download Page 75 | Manualshive

Page: 75 / 76

background image

VIBSCANNER 11.2010

75

Troubleshooting

If this doesn’t help, clear the current action by pressing the
joystick.
If this doesn’t help, try to reset the device.
If the problem persists, return the device for repair.

• Symptom: The following message appears on the display:

** Filesystem Error **
Media status == ....
Volume == .....
Serial # == ....
Volume is ....
.....
** Select Action **
Retry

Abort

Meaning:
A serious error occurred while accessing the internal
VIBSCANNER hard disc.

What to do:
Retry the current action by pressing the left button (ESC
key). If this doesn’t help, try to abort by pressing the right
button (function key). If this doesn’t help, clear the current
action by pressing the joystick. If this doesn’t help, try to
reset the device.

If the problem persists, return the device for repair.

How to set the device into boot mode

• Connect the battery charger to the device and to the

mains.

• Press all three buttons (the left key, the right key and the

joystick) for at least 5 seconds.

• Release the joystick, but keep the left and right button

pressed.

• After 1 second, release the left and right button. The

blue LED should now flash slowly.

To leave the boot mode, reset the device.

How to reset the device

• Press both the keys and the joystick at the same time for

approx. 5 seconds.

• Release the keys and the joystick to switch the instru-

ment on again.

«
...
73
74
75
76
»

Summary of Contents for VIBSCANNER VIB 5.400













































































Reviews:

No comments

Related manuals for VIBSCANNER VIB 5.400

Brand: rainforest Pages: 2

Brand: Major tech Pages: 16

Brand: Zoetis Pages: 2

Brand: Kawai Pages: 64

Brand: Kawai Pages: 28

Brand: Kawai Pages: 28

Brand: Kawai Pages: 72

Brand: Caen Pages: 63

Brand: Caen Pages: 35

Brand: LaMotte Pages: 32

Brand: Keysight Technologies Pages: 10

Brand: TEA Pages: 10

Brand: Ditel Pages: 2

Brand: Keithley Pages: 350

Brand: Anslut Pages: 11

Brand: Silverline Pages: 2

NEO MP18X Series

Brand: MA Pages: 3

Brand: Andor Technology Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands