54
Connecting to the RS-232C Port at the Host
Section 2-6
CS/CJ-series CPU Units:
CS1G/H-CPU
@@
-E (-V1)
CS1G/H-CPU
@@
H
CJ1G-CPU
@@
Connect to the built-in RS-232C port of the CPU Unit, or the RS-232C port of
the Communications Board. Note that the connection to a peripheral port
must be made via an RS-232C Adapter (CS1W-CN118) specially designed
for connecting to a peripheral port.
PLC Setup
When connecting to a CS/CJ-series CPU Unit, set the following communica-
tions conditions for the PLC Setup. Since the settings shown below are the
PLC default settings for the CPU Unit, no change to the PLC Setup is neces-
sary as long as the baud rate is maintained at 9,600 bps.
Note
Set the Host Link baud rate up to 115,200 bps with the memory switch at the
NT20. When the baud rate is set to 19,200 bps, the PLC Setup of the CPU
Unit need to be changed.
Either set the PLC Setup directly from a Programming Device (Programming
Console), or transmit the PLC Setup made at a Programming Device (CX-
Programmer) to the CPU Unit.
For details on PLC Setup, refer to the
SYSMAC CS Series Operation Manual
(W339-E1-
@
) or
SYSMAC CJ Series Operation Manual
(W393-E1-
@
).
When using the built-in RS-232C port of a CS1G/H, CS1G/H-H, or CJ1G
When using the peripheral port of a CS1G/H, CS1G/H-H, or CJ1G
Item
Setting at Host
Baud rate
Set the same speed as set at the NT20 (See note.)
Stop bits
2 stop bits
Parity
Even
Data length
ASCII 7 bits
Unit No. for the Host Link
00
Word address
Writing Value
Settings
CIO 160
8000
Host Link mode, data length 7 bits,
2 stop bits, even parity
CIO 161
0000
Baud rate: 9,600 bps.
0007
Baud rate: 19,200 bps.
0008
Baud rate: 38,400 bps.
0009
Baud rate: 57,600 bps.
000A
Baud rate: 115,200 bps.
CIO 166
0000
Unit #00
Word address
Writing Value
Settings
CIO 144
8000
Host Link mode, data length 7 bits,
2 stop bits, even parity
CIO 145
0000
Baud rate: 9,600 bps.
0007
Baud rate: 19,200 bps.
0008
Baud rate 38,400 bps.
0009
Baud rate 57,600 bps.
000A
Baud rate 115,200 bps.
CIO 150
0000
Unit #00
Summary of Contents for NT20
