Oki C810 Maintenance Manual Download Page 79

Page: 79 / 253

44015503TH Rev. 1

78 /

Oki Data CONFIDENTIAL

4. REPLACEMENT OF PARTS

4.2.11 operator panel Assy.

(1) Open the top cover.

(2) Open the multi-purpose tray.

(3) Open the front cover.

(4) Remove the left and right side covers (see sections 4.2.3 and 4.2.4).

(5) Remove the plate shield Assy. (see section 4.2.7, (2)).

(6) Detach and unclamp (at the two points) the FFC of the operator panel Assy.

(7) Unlatch the operator panel cover Assy. at the two points A to remove it and, at the

same angle as shown left below, remove the operator panel cover.

Top cover

Front cover

Multi-purpose tray

Clamp

FFC

Front cover

Operator panel cover Assy.

Unlatched points A

(8) Remove the three screws (silver-colored)

to detach the operator panel Assy.

(tool number 1). Be careful about a potential drop of the (black) cap

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 79 / 253

Search results

Summary of Contents for C810

Reviews: