manualshive.com logo in svg

Oki C810, Maintenance Manual, Page: 209 / 253

Share
Download
Oki C810 Maintenance Manual Download Page 209

44015503TH  Rev. 1 

208 /

Oki  Data  CONFIDENTIAL

7.  TROUBLESHOOTING PROCEDURE

(16-3) Error caused by the defective mechanism

Check item

Check work

Action to be taken 

at NG

(16-3-1) Mechanical load applied to the ID unit

ID unit

 Check if a heavy mechanical load is being 
applied to the ID unit due to breakage of the 
waster toner belt, or not.

Replace the ID 
unit. 
If any attempt 
of using new 
ID unit as a 
trial is going 
to be made, 
be sure to use 
the System 
Maintenance 
Menu FUSE 
KEEP MODE.

 (16-3-2) Motor operating condition

ID motor

 Confirm that the respective ID motors work 
normally or not by using the Motor & Clutch Test 
of the self-diagnostic mode. 
Check if any extra load exists or not.

Replace the PU 
board or the ID 
motor.

7.5.2.(17)  Fuse cut error (error codes 150 to 155) 

(17-1)  Fuse cut error

Check item

Check work

Action to be taken 

at NG

(17-1-1) Check the system connection

FFC connecting the 
PU board and the 
toner sensor board 
(PRZ PCB)

 Check if the connector is connected in the half-
way only or not, and is inserted in a slanted 
angle or not at the SSNS connector 

 of the PU 

board, and at the SSNS connector 

 of the toner 

sensor board (PRZ PCB). 
Check if FFC has open-circuit of sheath of the 
FFC has not peeled off or not.

 Connect the 
FFC normally. 
Alternately, 
replace the FFC.

(17-1-2) Fuse cut circuit

PU board

Upon completion of the system connection 
check, turn off the power once and back on. The, 
check if the error occurs or not.

 Replace the PU 
board.

Summary of Contents for C810






























































































































































































































































Reviews:

No comments