Oki C810 Maintenance Manual Download Page 130

Page: 130 / 253

44015503TH Rev. 1

129 /

Oki Data CONFIDENTIAL

5. MAINTENANCE MENUS

5.3.2.2 normal self-diagnostic mode (level 1)

The normal self-diagnostic mode menus are as follows:

Option

Self-diagnostic menu

Adjustment

Maintenance

Utility

Switch scan test

SWITCH SCAN

Checks an input sensor or

switch.

No. 18

Motor and clutch

test

MOTOR&CLTCH

TEST

Tests the operation of a

motor or clutch.

No. 19

Test printing

TEST PRINT

Prints a test pattern stored

in the PU.

Unavailable

Color registration

adjustment test

REG ADJUST TEST

Judges the color

registration adjustment

mechanism as pass or fail.

No. 20

Density

adjustment test

DENS ADJ TEST

Judges the density

adjustment mechanism as

pass or fail.

No. 21

Consumable

counter display

CONSUMABLE

STATUS

Displays the usage of a

consumable.

No. 23

Consumable life

counter display

PRINTER STATUS

Displays the life counter of

a consumable.

No. 23

Factory-Shipping

mode switching

FACTORy MODE

SET

Switches between Factory

and Shipping modes

No. 24

Fuse status

display

Displays the status of a

fuse.

No. 24

Engine parameter

setting

SENSOR SETTING

Sets whether to enable

or disable error detection

performed by each sensor.

No. 25

NvRAM

parameter setting

NvRAM

PARAMETER

Must not be used.

Unavailable

5.3.2.2.1 Entering self-diagnostic mode (level 1)

Note! Entering the System Maintenance mode of C830 requires a password. Refer

to table 5-1 for description on it.

1. Turn on the printer while using the MENU up-arrow ( ) and MENU down-arrow ( )

button combination to enter the System Maintenance mode.

2. Press the MENU up-arrow ( ) or MENU down-arrow ( ) button more than one

time to display ENGINE DIAG MODE. Then press the ENTER button to display

DIAGNOSTIC MODE.

DIAGNOSTICMODE

XX.XX.XX FACTORY/SHIPPING

3. XX.XX.XX on the LCD display identifies the PU firmware version. The FACTORy

WORKING MODE setting is displayed in the right portion of the lower row. The

setting is normally S-MODE, which identifies Shipping.

4. Press the MENU up-arrow ( ) and MENU down-arrow (^a) button to go to each

self-diagnostic step (press the MENU up-arrow ( ) or MENU down-arrow (^a)

button to display the next or preceding menu option).

5.3.2.2.2 Exiting self-diagnostic mode

1. Turn of the printer and, after ten seconds, turn it on.

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 130 / 253

Search results

Summary of Contents for C810

Reviews: