manualshive.com logo in svg

Oki C810, Maintenance Manual, Page: 159 / 253

Share
Download
Oki C810 Maintenance Manual Download Page 159

44015503TH  Rev. 1 

158 /

Oki  Data  CONFIDENTIAL

7.  TROUBLESHOOTING PROCEDURE

7.5  troubleshooting method

When  a  trouble  occurs  in  this  printer,  perform  troubleshooting  by  following  the  steps 

described below.

7.5.1  LCD message list

Initializing

Panel display

ON

LINE
lamp

Inspec-

tion

lamp

Details

PLEASE WAIT

Off

Off

It is displayed until the RAM expansion of the CU
program is in progress.

Initializing

Off

Off

Indicates initialization of the controller side is in
progress.

EEPROM Reset

Off

Off

Indicates the controller side EEPROM is reset.
The conditions for resetting the EEPROM are
shown below.
• CU ROM is changed (Unmatch of the CU F/W 

version is detected.)

• Destination is changed.
• Forced initialization of EEPROM (System 

Maintenance Menu)

• Setting OEM by the PJL command.

RAM Check 
nnn%

Off

Off

Indicates that RAM check is in progress.
Percentage of the checked capacity against the
total capacity is shown in the second line.

Wait a Moment 
Network Initializing

Off

Off

Indicates the network initialization is in progress.

Flash Memory Format

Off

Off

Indicates that the flash memory formatting is in 
progress. If a resident/option flash memory that is 
not formatted yet is detected, it is displayed when 
the menu item [FLASH FORMAT] is selected 
from [MAINTENANCE MENU] of the System 
Maintenance Menu. Because the above menu item 
is internally use only and is not disclosed to user, 
this status does not occur in the user environment. 

Checking File System

Off

Off

Indicates that the HDD File System is being checked. 
The checking process of File System is available 
for actuating from [Storage Setup] - [Check File 
System] of Boot Menu.

Trouble occurs

The trouble that is 
displayed by the 
LCD message.

Use the "LCD message 
list” and perform 
troubleshooting. (Refer  
to 7.5.1.)

Perform more detailed 
troubleshooting using the 
Troubleshooting Flow. (Refer  
to 7.5.2.)

Abnormal printed 
image (and the 
trouble that is not 
displayed by the 
LCD messages.) 

Perform more detailed 
troubleshooting using the 
Troubleshooting Flow. (Refer  
to 7.5.3.)

Summary of Contents for C810






























































































































































































































































Reviews:

No comments