Oki C810 Maintenance Manual Download Page 140

Page: 140 / 253

44015503TH Rev. 1

139 /

Oki Data CONFIDENTIAL

5. MAINTENANCE MENUS

4. Repeat steps 2 and 3 when necessary.

5. Press the BACK button to end the test (the state if step 1 is restored).

Color registration adjustment test item

Option

Detail

REG ADJ EXECUTE

Executes color registration adjustment.

REG ADJ RESULT

Displays the result of color registration adjustment.

BLT REFLECT TEST

Judges whether color registration adjustment belt

reflection is proper.

BLT REFLECT RSLT

Displays the result of color registration adjustment

belt reflection judgment.

5.3.2.7 Density adjustment test

The density adjustment test is used for performing a density adjustment function test and

displaying the result of it to judge whether the density adjustment mechanism is proper.

Chapter 2 about description on density adjustment should be followed for recovery from an

error.

1. Enter the self-diagnostic-mode and, until the following message appears, press the

MENU up-arrow ( ) or MENU down-arrow ( ) button.

DENS ADJ TEST

2. Press the ENTER button. The following message appears. Press the MENU up-

arrow ( ) or MENU down-arrow ( ) button until the intended option appears.

DENS ADJ TEST

DENS ADJ EXECUTE

3. Press the ENTER button. The displayed option is performed:

When the displayed option is DENS ADJ EXECUTE:

Density adjustment test (the ONLINE lamp starts blinking) is performed.

When the test ends, the upper display shows the result of the test (OK or a

error name), the lower display shows ‘****RESULT’.

DENS ADJ RESULT

Pressing the MENU up-arrow ( ) button displays the next test result. Pressing

the MENU down-arrow ( ) button displays the preceding test result. Press the

BACK button to return to step 2.

Pressing the CANCEL button during the test cancels the test (turning on the

ONLINE lamp), restoring the state of step 2.

When the displayed option is DENS ADJ RESULT:

Same as of REG ADJ EXECUTE

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 140 / 253

Search results

Summary of Contents for C810

Reviews: