manualshive.com logo in svg

Oki C810, Maintenance Manual, Page: 171 / 253

Share
Download
Oki C810 Maintenance Manual Download Page 171

44015503TH  Rev. 1 

170 /

Oki  Data  CONFIDENTIAL

7.  TROUBLESHOOTING PROCEDURE

Display on operator panel

ON

LINE
lamp

Inspec-

tion

lamp

Contents

Code

nnn

Change the toner cartridge. 

%COLOR%

For details please see Help.

Off

Blink

Indicates that the waster toner of %COLOR% is 
full requiring Replace toner.

Error 415: Magenta

Error 416: Cyan

(This error does not occur in the yellow and 
black toner.)

When the cover is opened/closed, it changes to 
the warning status making possible to perform 
printing  of approx 50 copies. 

Error 

415

416

Change the Toner cartridge. 

%COLOR%

For details please see Help.

Off

Blink

Indicates that the printer runs out of toner. 
When the cover is opened/closed, it changes to 
the warning status.

Error 410: yellow

Error 411: Magenta

Error 412: Cyan

Error 413: Black

Error 

 

410

411

412

413

Toner cartridge is incorrect. 

%COLOR%

For details please see Help.

Off

Blink

Indicates that it is not the Toner cartridge for the 
use of this printer. 
It recovers by changing the Toner cartridge for 
the use of this printer.

Error 554: yellow

Error 555: Magenta

Error 556: Cyan

Error 557: Black

Error 

 
 

554

555

556

557

Toner cartridge for other 
company’s printer use is in 
the printer. 

%COLOR%.

For details please see Help. 

Off

Blink

Indicates that it is not the Toner cartridge for the 
use of this printer. 
It recovers by changing the Toner cartridge for 
the use of this printer.

Error 614: yellow

Error 615: Magenta

Error 616: Cyan

Error 617: Black

Error 

 
 
 

614

615

616

617

Display on operator panel

ON

LINE
lamp

Inspec-

tion

lamp

Contents

Code

nnn

Toner cartridge for other 
company’s printer use is in 
the printer. 

%COLOR%. 

For details please see Help.

Off

Blink

Indicates that it is not the Toner cartridge for the 
use of this printer. 
It recovers by changing the Toner cartridge for 
the use of this printer.

Error 620 : yellow

Error 621 : Magenta

Error 622 : Cyan

Error 623 : Black

Error 

 
 

620

621

622

623

The Toner cartridge is not 
genuine goods. 

%COLOR%

Terminate the printing for 
protecting the printer. 

For details please see Help.

Off

Blink

Indicates that it is not the Toner cartridge for the 
use of this printer.  
It recovers by changing the Toner cartridge for 
the use of this printer. 

Error 550 : yellow

Error 551 : Magenta

Error 552 : Cyan

Error 553 : Black

Error 

 
 

550

551

552

553

Toner cartridge is not set.

%COLOR%

For details please see Help

Off

Blink

Indicates that Toner cartridge is not installed.

Error 610: yellow 

Error 611: Magenta

Error 612: Cyan

Error 613: Black

Error

610

611

612

613

Check toner cartridge.

%COLOR%

Off

Blink

Indicates that the toner sensor has detected the 
error.

Error 540: yellow

Error 541: Magenta

Error 542: Cyan

Error 543: Black

Error 

540

541

542

543

Pull out the Tray.

Paper is left in it. 

%TRAy%

For detail please see Help. 

Off

Blink

Indicates due to occurrence of paper jam, the 
continuously fed paper keep remaining in the 
printer.  

Error 631: Tray 1 cassette

Error 632: Tray 2 cassette

Error 633: Tray 3 cassette

Error 

 

631

632

633

Open the cover.

Paper is remaining.

Front cover

For details please see Help.

Off

Blink

Indicates due to occurrence of paper jam, the 
continuously fed paper keep remaining in the 
printer.  

Error 637: J0: Paper Feed Path

Error 

 

637

Summary of Contents for C810






























































































































































































































































Reviews:

No comments