Oki C810 Maintenance Manual Download Page 36

Page: 36 / 253

44015503TH Rev. 1

35 /

Oki Data CONFIDENTIAL

3. INSTALLATION

3.4 List of components and accessories

• Check to make sure that the components are free from damage, dirt or other

irregularities in their appearance.

• Ensure that none of the accessories to the components is missing and that they are

free from breakage or other flaw.

• If any irregularity is discovered, contact the user management section for instructions.

Personal injury may occur.

Since the printer weights approximately 40 kg, it should be lifted by two or more

people.

Printer (main unit)

Image drum cartridges (one each of cyan, magenta, yellow, and black) installed in the

printer

Toner cartridges (one each of cyan, magenta, yellow, and black) installed in the printer

Inform the user that the toner cartridges and image drum cartridges can be separated

one from the other.

Printer software CD-ROM

Power cord

User’s manual (Setup)

User’s manual (CD-ROM)

Quick Guide

Bag for Quick Guide

Note! No printer cable is supplied with the printer.

Summary of Contents for C810






























































































































































































































































Search results

Summary of Contents for C810

Reviews:

Oki C810, Maintenance Manual, Page: 36 / 253

Search results

Summary of Contents for C810

Reviews: