manualshive.com logo in svg

Oki C810, Maintenance Manual, Page: 189 / 253

Share
Download
Oki C810 Maintenance Manual Download Page 189

44015503TH  Rev. 1 

188 /

Oki  Data  CONFIDENTIAL

7.  TROUBLESHOOTING PROCEDURE

Jam release level

(c)  If you see the bottom edge of the  jammed paper pull out the  jammed paper, 

slowly while pulling up the jam release lever of the fuser unit. 

(d)  If f paper is jammed in the fuser unit, bending down the fixed lever (Blue) to the 

front side, remove the fuser unit. 

 

Pull up the jammed release level (2 levels) and then pull out the jammed paper 

to the front side.

 

Holding up the handle and return the fuser unit to the printer gently.

 

Bending the fixed level (Blue) of the fuser unit to the backside and fix it. 

Jam release level of fuser unit

Handle

Fixed level of fuser unit (Blue)

Fixed level of fuser unit (Blue)

Handle

(b)  If you do not see the top edge or the bottom edge of jammed paper, pull out 

the jammed paper slowly while heaving it. 

Paper

Fuser unit

Summary of Contents for C810






























































































































































































































































Reviews:

No comments